Shot Peening Springs: How It Improves Fatigue Life and What to Specify

Author: Jenny Xu

Published: Nov 20, 2025

Updated: Nov 14, 2026

Shot peening is a cold-working process that blasts a part with small round media such as steel shot, conditioned cut wire or ceramic beads. Each impact stretches a thin surface layer, and the material beneath pushes back, leaving the surface in compressive residual stress. For springs this matters because fatigue cracks almost always start at the surface, and compression at the surface makes them much harder to start.

Why springs benefit from shot peening

In a helical compression or extension spring the highest stress is torsional shear at the inside of the coil, right at the wire surface. In a torsion spring it is bending stress at the inside surface of the coil. Small surface flaws from wire drawing, coiling tools or decarburisation act as crack starters. The compressive layer from peening offsets part of the tensile stress the spring sees in service, so cracks start later and grow more slowly.

The gain is largest for springs that are both highly stressed and highly cycled. Fatigue design charts for springs, such as the Goodman diagrams in EN 13906-1, give shot-peened springs a noticeably higher permissible stress range than unpeened springs of the same material.

Springs that are usually shot peened

  • Engine valve springs and other high-speed, high-cycle springs
  • Die springs working at high deflection in presses and moulds
  • Heavy hot coil springs for rail, mining and vehicle suspension
  • Disc springs under dynamic load
  • Clutch, damper and actuator springs in power equipment

Springs that carry a static or lightly cycled load, such as many latch and cover springs, gain little, and very fine wire is hard to peen without damage.

Intensity and coverage

Intensity is the energy of the peening stream. It is measured on Almen strips, thin spring-steel test strips to SAE J442 that bow into an arc when peened on one side. The arc height at saturation, the point after which doubling the exposure time raises the arc height by no more than 10%, is the intensity, quoted with the strip type, for example 0.30 mmA. Thinner wire needs a lower intensity so the compressive layer does not damage or distort the section.

Coverage is the share of the surface hit by at least one impact, checked under magnification or with a fluorescent tracer. 100% coverage means no unpeened area is visible, and many spring specifications call for 100% to 200%. More coverage costs time without adding much benefit, while gaps leave the original surface exposed.

Media must be screened so that broken, sharp particles are removed, because they cut the surface instead of denting it. Common references are SAE J2441 for the peening process, SAE J827 for cast steel shot, SAE J441 for cut wire shot and AMS 2430 for automatic peening.

Where peening sits in the process route

For a cold-coiled compression spring a typical route is coil, stress relieve, grind the ends, shot peen, preset, then coat or plate. The order follows two rules. Peening must come after end grinding, which would otherwise cut the compressive layer away, and after any heat treatment hot enough to relax it. Plating comes last, and electroplated high-strength springs need hydrogen embrittlement relief baking; see this article on plating risk.

Two variants are worth knowing. Dual or double peening adds a second pass with smaller media to raise the compressive stress right at the surface, and is common on valve springs. Stress peening peens the spring while it is held compressed in its working direction, which leaves a deeper and stronger compressive layer and is used on suspension springs.

What to put on the drawing or RFQ

  • Intensity range and Almen strip type, for example 0.25–0.35 mmA
  • Minimum coverage, for example 100%
  • Media type and size, or leave it to the supplier if only the result matters
  • Areas to peen and areas to mask, such as hook ends or ground faces
  • Process order relative to stress relief, presetting and coating
  • Records required, such as Almen strip results per batch and a coverage check

Wanjin plans shot peening and presetting against the duty cycle on each drawing and states them in the quotation, as part of the manufacturing processes reviewed with the drawing. For a high-cycle spring, send the working stroke, frequency and target life with the RFQ so the peening specification can be agreed before sampling.

Key Takeaways

  • Shot peening leaves a compressive layer at the surface, where spring fatigue cracks start.
  • Specify intensity (Almen arc height with strip type) and coverage, not just "shot peen".
  • Peen after end grinding and heat treatment, and before coating.
  • It pays most on highly stressed, high-cycle springs; static springs gain little.

Frequently Asked Questions

Does shot peening increase spring life?

Yes, for springs that fail by fatigue. The compressive surface layer delays crack initiation, so peened springs tolerate a higher stress range for the same life. It does not help a spring that fails by overload, corrosion or relaxation.

What is Almen intensity?

A measure of peening energy: the arc height of a standard SAE J442 test strip peened to saturation, quoted with the strip type, such as 0.30 mmA.

Can stainless steel springs be shot peened?

Yes. Stainless springs are peened too, usually with stainless or ceramic media so that no iron is left on the surface to rust.

Related spring types

Related Posts

Tags