Spring Rate Calculator for Compression, Extension, Torsion & Disc Springs

Estimate spring rate (spring constant), load, stress and solid height for compression, extension and torsion springs, and load, rate and stress for Belleville washers (disc springs) and disc stacks. Switch between mm/N and in/lbf. Results are design estimates; send your drawing for a manufacturing review.

Formulas used

  • Compression / extension: k = G·d⁴ / (8·D³·Nₐ); τ = K_w·8·F·D / (π·d³); K_w = (4C − 1)/(4C − 4) + 0.615/C
  • Torsion: k′ = E·d⁴ / (10.8·D·N) N·mm/turn; σ = K_i·32·M / (π·d³)
  • Disc / Belleville: F = [4E / (1 − μ²)] · [t⁴ / (K₁·De²)] · (s/t) · [(h₀/t − s/t)·(h₀/t − s/2t) + 1]; K₁ = (1/π)·[(δ − 1)/δ]² / [(δ + 1)/(δ − 1) − 2/ln δ], δ = De/Di; σOM = −[4E / (1 − μ²)] · [t² / (K₁·De²)] · (s/t) · 3/π (DIN 2092 / EN 16984)

How to calculate spring rate

Spring rate is the force needed to deflect a spring by one unit of length. For a helical compression or extension spring it follows from Hooke's law, F = k·x, and the spring's geometry.

  • Measure wire and diameter: Measure the wire diameter d and the outside diameter OD. The formula uses the mean diameter D = OD − d.
  • Count the active coils: Count the total coils Nₜ and subtract the inactive end coils: two for closed ends, one for plain ground ends, none for plain ends.
  • Choose the material: The shear modulus G sets the stiffness: about 79 GPa for carbon spring steel, 69 GPa for 302 stainless and 41 GPa for phosphor bronze.
  • Check stress and travel: Multiply the rate by the working deflection to get the load, then check Wahl-corrected stress, spring index and travel to solid height.

Worked example

Carbon spring steel wire, d = 2 mm, OD = 20 mm (D = 18 mm), 10 total coils with closed and ground ends (Nₐ = 8), G = 79.3 GPa:

k = 79 300 × 2⁴ / (8 × 18³ × 8) ≈ 3.40 N/mm (19.4 lbf/in)

Belleville washer calculator example (DIN 2093 A 40)

Spring steel disc, De = 40 mm, Di = 20.4 mm, t = 2.25 mm, l₀ = 3.15 mm (h₀ = 0.9 mm), E = 206 GPa, μ = 0.3, deflected to s = 0.75·h₀:

K₁ ≈ 0.686 · F(s = 0.675 mm) ≈ 6 500 N (1 461 lbf) · F(flat) ≈ 8 456 N

Variables in the spring rate formula

  • k: Spring rate or spring constant, in N/mm (or lbf/in). 1 N/mm ≈ 5.71 lbf/in.
  • G: Shear modulus of the wire material, in GPa (× 1000 for N/mm²).
  • d: Wire diameter.
  • D: Mean coil diameter, D = OD − d. The rate falls with the cube of D.
  • Nₐ: Number of active coils: the coils that are free to deflect.
  • C: Spring index, C = D/d. A practical range is about 4 to 12.
  • K_w: Wahl correction factor, (4C − 1)/(4C − 4) + 0.615/C, for coil curvature and direct shear.

Spring rate FAQ

What is spring rate?

Spring rate, also called the spring constant, is the force required to compress or extend a spring by one unit of length, for example 3.4 N/mm. For a linear spring the force rises in proportion to deflection (F = k·x).

What is the spring rate formula for a compression spring?

k = G·d⁴ / (8·D³·Nₐ), where G is the shear modulus, d the wire diameter, D the mean coil diameter and Nₐ the number of active coils. Doubling the wire diameter makes the spring 16 times stiffer; doubling the mean diameter makes it 8 times softer.

Is spring rate the same as spring constant?

Yes. Both mean force per unit deflection. "Spring rate" is more common on spring drawings and catalogs; "spring constant" is the physics term from Hooke's law.

How do I convert spring rate from N/mm to lbf/in?

Multiply N/mm by 5.710 to get lbf/in, or divide lbf/in by 5.710 to get N/mm. For N/m, multiply N/mm by 1000.

Why does a measured spring rate differ from the calculation?

Real springs vary with wire diameter tolerance, the actual number of active coils, end-coil contact, material modulus and pitch. The rate is also less linear near free length and solid height, so rate is commonly measured between about 20% and 80% of the available travel.

Can Wanjin manufacture a spring from my calculation?

Yes. Send the calculated dimensions, the load you need at a working length, material, end type and quantity. Wanjin reviews feasibility, tolerances and test requirements against your drawing before sampling.

How do you calculate the load of a Belleville washer?

Use the Almen–László formula from DIN 2092 / EN 16984: F = [4E / (1 − μ²)] · [t⁴ / (K₁·De²)] · (s/t) · [(h₀/t − s/t)·(h₀/t − s/2t) + 1], where K₁ depends only on the diameter ratio De/Di. A DIN 2093 A 40 disc (40 × 20.4 × 2.25 mm) gives about 6.5 kN at 75% of its cone height.

How does stacking change a disc spring's load and travel?

Discs stacked in parallel (same direction) multiply the load at the same deflection; discs stacked in series (alternating direction) multiply the deflection at the same load. A stack of i series groups with n discs each carries about n times the single-disc load over i times its travel, with friction hysteresis from the parallel discs.

Related Posts

Related spring types

Estimates use nominal dimensions and typical room-temperature moduli. They are not a quotation, tolerance or acceptance value; feasibility, stress limits and fatigue life are confirmed in drawing review.