Springs in Series and Parallel: Formulas and Worked Examples
Author: Jenny Xu
Published: Nov 14, 2026
Updated: Nov 14, 2026
Springs combine in two basic ways. In parallel they share the same deflection and their constants add: k = k₁ + k₂. In series they carry the same force and their deflections add, so 1/k = 1/k₁ + 1/k₂. A parallel set is stiffer than any spring in it; a series set is softer and gives more travel.
Springs in parallel
Springs are in parallel when they sit side by side between the same two plates, so each is compressed by the same amount x. The total force is the sum of the individual forces, F = k₁·x + k₂·x, which gives k = k₁ + k₂ + … for any number of springs.
Example: a 5 N/mm and a 3 N/mm spring in parallel make 8 N/mm. Compressed 10 mm, the pair carries 80 N, split 50 N and 30 N. Each spring takes load in proportion to its own rate, so the stiffer spring is the one to check for stress.
Parallel springs must have the same free length to share load from the start. If the 3 N/mm spring is 2 mm shorter, only the 5 N/mm spring works for the first 2 mm, and at 10 mm the set carries 5 × 10 + 3 × 8 = 74 N, not 80 N.
Springs in series
Springs are in series when they are stacked end to end, so the same force passes through each one. Each deflects by F/kᵢ and the deflections add: x = F/k₁ + F/k₂, which gives 1/k = 1/k₁ + 1/k₂ + …. For two springs this is k = k₁·k₂ / (k₁ + k₂).
Example: the same 5 N/mm and 3 N/mm springs in series make 5 × 3 / (5 + 3) = 1.875 N/mm. Under 40 N the stiff spring deflects 8.0 mm and the soft spring 13.3 mm, 21.3 mm in total. The softer spring always takes the larger share of the travel, and the series rate is always lower than the softest spring in the set.
Quick reference
| Arrangement | Combined rate | Shared by every spring | Adds up |
|---|---|---|---|
| Parallel | k = k₁ + k₂ + … | Deflection | Force |
| Series | 1/k = 1/k₁ + 1/k₂ + … | Force | Deflection |
| n equal springs in parallel | n·k | Deflection | Force |
| n equal springs in series | k/n | Force | Deflection |
Dual-rate springs: series until one goes solid
A series pair gives a two-stage force curve when the soft spring reaches its solid height before the stiff one. Until then the set runs at the series rate; after that only the stiff spring deflects. If the 3 N/mm spring has 6 mm of travel to solid, it closes at 18 N and 9.6 mm of total deflection. Above 18 N the rate is 5 N/mm, so 40 N needs 9.6 + 22/5 = 14.0 mm.
Sets like this give a soft start and a firm end, as with the tender and main springs of a vehicle suspension. The same two-stage effect can be wound into a single variable-pitch compression spring.
Nested compression springs
Two compression springs fitted one inside the other work in parallel: both see the same deflection, and their rates add. Nesting packs more load into a fixed diameter, which is why it is common in heavy machinery and rail suspension built from hot coil springs. Wind the inner and outer springs in opposite hands so their coils cannot interlock, leave radial clearance for the outside diameter to grow under compression, and check each spring's stress on its own, because each carries load in proportion to its rate.
Disc spring stacks: series and parallel in one
Disc springs are stacked using both rules. Discs nested in the same direction act in parallel and multiply the force; discs placed face to face act in series and multiply the deflection. For a stack of i groups in series, each with n discs in parallel: F ≈ n·F₁, s = i·s₁, and the unloaded stack length is L₀ = i·[l₀ + (n − 1)·t], where F₁ and s₁ are the force and deflection of one disc, l₀ its free height and t its thickness.
Example: a DIN 2093 A 40 disc (t = 2.25 mm, l₀ = 3.15 mm, h₀ = 0.9 mm) carries about 6.5 kN at 75% of h₀, a deflection of 0.675 mm. Five groups of two discs carry about 13 kN at 3.4 mm of stack travel, with L₀ = 5 × (3.15 + 2.25) = 27.0 mm. Friction between nested discs raises the loading force and lowers the return force by a few percent per sliding face, so parallel stacks show hysteresis. The disc spring stack page and the Belleville mode of the calculator cover these combinations.
Double torsion springs
A double torsion spring is two coils wound in opposite directions and joined by a central loop. When the loop is loaded, both coils turn through the same angle, so they act in parallel and the torque rate is about twice that of one coil.
Design checks for combined springs
- Parallel: match the free lengths, or stagger them on purpose to get a stepped rate.
- Series: every spring carries the full force, so check the stress in the weakest one, and guide long series stacks on a rod with separator washers so they cannot buckle.
- Both: the combined rate changes the natural frequency of the system, f = (1/2π)·√(k/m).
- Both: specify the force of the assembled set at its working lengths, so the set is tested the way it works.
Use the spring rate calculator to find each spring's rate, then combine the rates with the formulas above. Hooke's law gives the force and stored energy of the combined set.
Key Takeaways
- Parallel: k = k₁ + k₂; springs share deflection, and the stiffer one carries more load.
- Series: 1/k = 1/k₁ + 1/k₂; springs share force, and the softer one takes more travel.
- A series pair becomes a dual-rate spring when the softer spring goes solid first.
- Disc spring stacks: n discs in parallel multiply the force, i groups in series multiply the deflection.
Frequently Asked Questions
Is a spring stiffer in series or in parallel?
In parallel. Two equal springs in parallel are twice as stiff as one; in series they are half as stiff.
How do you calculate two springs in series with different constants?
Use k = k₁·k₂ / (k₁ + k₂). A 5 N/mm and a 3 N/mm spring in series give 1.875 N/mm, lower than either spring alone.
What happens if springs in parallel have different free lengths?
The longer spring takes load first and the shorter one joins when it is reached, so the force–deflection line steps up in slope. Match the free lengths unless that step is wanted.